No products in the cart.
Lower home heating expenses with the Custom Zero-Clearance Fireplace Heater Kit. This fireplace heat gives to the enjoyment of comforting warmth that the you won’t be able to get fully from a common fireplace. The natural heat of 80% created by traditional hearths is gets lost through the chimney. This high performing energy-efficient fireplace blower provides an increased heat temperature to go around your home at a low heating cost. This grate heater has a unique setup to superheat the air inside the exchanger tubes to over 500F enabling it to send out up to 60000 BTUs of heat sufficient to give warmth into a large room or two. It excellently fits into most smaller or zero-clearance pre-fab fireplaces and operates without that use of power by converting heat naturally through the heavy aluminized steel tubing then distributed into your home. These sturdy aluminum tubes deliver a lasting usage of this product. The optional blower has the capacity to send out up to 60000 BTUs of heat when used with the hearth heater. This blower is installed on either the left or right side of your Fireplace Hearth Heater. Five and six tube units have a 2-speed blower 50 CFM – High 30 CFM – Low. Units with seven or more tubes have a 148 CFM blower with a variable speed control. This product gives a low cost heat energy. It delivers up to 48000 BTUs of heat or more with the six through ten-tube models – read the Additional Info tab for more details. This fireplace blower fits smaller fireplaces. Get this into your home with a simple installation. It offers 500% heat output increase. Each unit has heavy tubing for long life use. It works during power outages. The Heat Pipes are made of a 0.063-gauge aluminized steel which inhibits burn through and rust. The sizes in special order require three to four weeks to manufacture. For larger fireplaces see the Fireplace Heater . Note: This heater may be used with a gas log lighter as long as clearances allow for placement under the grate. BEFORE YOU BURN: Normally there will be a smell on the first burn as the oil in the tubes will burn off. WARNING: If you have birds and animals in the house they should be removed from the house on the first burn. People that are asthmatic and children should also not be in the area during the first burn. Additional Information: Number of Tubes Front Width Rear Width Front Height Rear Height Depth BTU Per Hour Max* 4 Tubes standard size 14 1/814 1/817 7/814 1/217 1/4up to 48000 5 Tubes custom size 18 1/818 1/817 7/814 1/217 1/4up to 58000 6 Tubes custom size 222217 7/814 1/217 1/4up to 68000 7 Tubes custom size 25 1/225 1/217 7/814 1/217 1/4up to 78000 8 Tubes custom size 29 3/429 3/417 7/814 1/217 1/4up to 88000 9 Tubes custom size 33 5/833 5/817 7/814 1/217 1/4up to 98000 10 Tubes custom size 37 1/237 1/217 7/814 1/217 1/4up to 108000 * BTU output will vary depending on type of wood size of fire fireplace size etc. Fireplace Heater Instructions Specifications: Low cost Delivers up to 48000 BTU’s of heat or more with 6 thru 10 tube models – see Additional Info tab For use in smaller fireplaces Simple installation 500% heat output increase Heavy tubing for long life Works without power Heat Pipes are made of .063 gauge aluminized steel which inhibits burn thru and rust. 16 gauge aluminized metal tubing Diameter of tubes 1-3/4Optional Blower Delivers up to 60000 BTU’s of heat when used with a hearth heater Units with 5 or 6 tubes have a 2 speed blower 50 CFM – High 30 CFM – Low. Flexible blower connector is adjustable from 8to 18″. Blower Box can mount on left or right side by flipping the manifold. The Fireplace Heater is made dramatically with increased convection heat hot air coming from your fireplace. The unique design of this grate heater superheats the air within the exchanger tubes to over 500F and can produce up to 48000 BTUs of heat enough to heat a large room or two. It fits into most smaller or zero-clearance pre-fab fireplaces and works without power by converting heat naturally through the tubing and into your home.